Vacuum Tower Acidic Water Tamed by CDFU Flotation Plus KHC Coalescing
Vacuum tower overhead acidic water is one of those streams every refinery handles and few handle gracefully. It originates at the top of the vacuum distillation column, and it concentrates the ugly fraction of refining wastewater: high concentrations of sulfides, ammonia nitrogen, phenols, cyanide and other hazardous substances. These compounds are highly toxic, accumulate easily and pose a serious threat to the environment. The pH usually runs low, meaning the water is acidic as its name says, which makes every downstream treatment step harder still.
Each contaminant brings its own complication. Sulfides corrode equipment and consume oxidants on contact, phenols poison the microorganisms that later biological stages depend on, and cyanide complicates any scheme that recycles water internally. Ammonia nitrogen loads the downstream nitrogen removal step. None of these is exotic on its own; together, at the concentrations the vacuum tower delivers, they make the stream unlike any other in the refinery water balance.
Reading the stream before designing the plant
The design error to avoid is treating acidic water as generic oily wastewater. The sulfide and cyanide load narrows the equipment choices, since materials must tolerate the chemistry and any process that aerosolises the water needs containment. The phenol load matters for the biology later in the train. Sizing the front-end units for the worst emulsified condition, rather than the average, is what keeps effluent quality stable through feed swings.
Why the conventional toolbox disappoints
Gravity settling is simple and easy but demands long settling times and achieves limited separation. Chemical precipitation goes the other way: it needs large amounts of chemicals, which raises treatment cost and may cause secondary pollution of its own. Between slow settling and expensive chemistry, efficiently and economically treating vacuum tower overhead acidic water has remained a long-standing industry challenge.
Emulsification is the hidden difficulty. Overhead acidic water carries natural surfactants and fine solids that pin oil droplets apart, so the droplets a settler receives are often two orders of magnitude smaller than they were at the point of origin. Any process built on gravity must therefore either grow the droplets or accept a very long residence time, and the economics of refinery plot space rarely permit the latter. Growing the droplets is therefore the cheaper engineering choice, and it is exactly what coalescing media are for.
The CDFU and KHC route
To tackle that challenge, SINOKLE Technology launched a new process built around two core units: CDFU (cyclonic dissolved-air flotation) and KHC (coalescing oil remover). The train is deliberately simple. First, the CDFU unit pretreats the wastewater: using the principles of cyclonic separation and dissolved-air flotation, it removes suspended solids, oil and part of the dissolved organic matter. The water then enters the KHC coalescing oil remover, where special coalescing media coalesce small oil droplets into large ones, completing the oil-water separation.
How each unit earns its place
CDFU works through cyclonic action: suspended solids and oil particles in the wastewater rapidly collide with and adhere to the micro-nano bubbles generated from dissolved air, forming flotation flocs that rise to the water surface and achieve solid-liquid separation. The KHC coalescing oil remover exploits the oleophilic and hydrophobic properties of its coalescing media to aggregate tiny oil droplets into large droplets, which then settle under gravity, achieving efficient oil-water separation without chemical assistance.
Operationally, the pairing is forgiving. The CDFU has no chemical system to keep in balance, and its cyclonic stage tolerates the feed swings that vacuum column switchovers produce. The KHC stage has no moving parts in the coalescing zone, so its performance drifts slowly and predictably rather than failing suddenly. Both units shed their collected oil as a concentrated phase that can rejoin the refinery slop system, closing the material loop instead of exporting waste.
What the process delivers
- Efficient oil-water separation with high removal efficiency and stable effluent quality.
- No dependence on large amounts of chemicals, avoiding secondary pollution and reducing treatment cost.
- Small footprint, a high degree of automation and stable, reliable operation.
A highly emulsified acidic wastewater treatment project at a refinery demonstrated the train in service, and the same features give the process broad prospects in coking acidic water, where emulsification and toxicity run higher still. For a stream that was once written off as uneconomic to treat, the pairing of a fast physical pretreatment with a chemical-free coalescing stage has turned vacuum tower overhead acidic water into a solvable problem, handled efficiently, in an environmentally friendly way and at a reasonable cost.
Refineries evaluating the route should pilot it on their own overhead water, since the emulsion stability of acidic water varies with crude slate. The trial is short, the equipment is skid-mounted, and the numbers it produces translate directly into the full-scale design, which is why the route has moved from curiosity to shortlist in a single project generation.