From Furnace Waste to Working Catalyst: Reusing FCC Spent Catalyst for Ozonation
Fluid catalytic cracking (FCC) sits at the heart of the modern refinery, and it burns through catalyst relentlessly. Deactivation comes from heavy metal deposition, coking and similar mechanisms, so cracking units retire large quantities of spent catalyst every year. The spent material carries heavy metals and hazardous substances that threaten the environment and human health if mishandled, yet it also holds abundant aluminum, silicon and potentially active components, which is why its resource utilization has become a focus of industry attention.
The scale of the flow deserves attention. A single large cracking unit cycles tonnes of catalyst daily, and even with continuous regeneration a fraction is bled off and replaced to keep the equilibrium activity target. Multiplied across a national refining fleet, the spent stream runs into tens of thousands of tonnes per year, which is large enough to sustain a dedicated recovery industry and small enough, per plant, to handle with conventional solids processing equipment.
The two conventional outlets, and why both disappoint
Landfill occupies land resources and carries environmental risk. Regeneration for reuse is cleaner in principle but limited by technical complexity and cost. Neither route recovers value proportionate to what the spent catalyst still contains, so the search for high-value utilization routes carries practical weight, not just academic interest.
Regulation sharpens the economics further. Spent cracking catalyst is classified as hazardous waste in several jurisdictions, so landfill fees and manifesting requirements raise the cost of the default route year by year. Every tonne diverted into recovery avoids that fee and returns saleable metal or material, turning a compliance cost into a modest revenue line.
Recovery routes that already pay
A research team proposed an oxidative roasting, alkaline roasting and wet ball-milling leaching process that efficiently recovers tungsten, molybdenum and other metals from spent catalysts, with extraction rates of 87.23% and 99.50% respectively. Magnetic separation recovers some components that remain active. Spent catalyst also serves as raw material for new materials: synthesizing Y-type zeolite from it achieves waste utilization while improving the catalytic performance of the zeolite itself.
Zeolite synthesis is the sleeper route among these options. Molecular sieves command prices far above bulk recovered metal, and the specifications they must meet, notably silica-to-alumina ratio, crystallinity and cation exchange capacity, are properties the spent FCC catalyst already possesses in useful measure. Converting it into a commercial sieve shortens the synthesis recipe instead of complicating it, which is why several refiners now treat their spent catalyst inventory as a feedstock warehouse rather than a liability.
From spent catalyst to ozone catalyst
The most consequential route for water treatment is the preparation of high-efficiency ozone catalysts. The spent catalyst is calcined and ground, mixed with binders and active metal salts such as manganese, cerium and iron, then processed through extrusion, drying and calcining. The product is an ozone oxidation catalyst with high mechanical strength and good catalytic activity. In phenol-bearing wastewater reactions, a catalyst with manganese as the active component achieved a phenol removal rate of 94.36% and a COD removal rate of 78.62%, real performance on exactly the refractory organics that ozone catalytic oxidation targets.
A one-step preparation simplifies the route further: the spent catalyst is mixed with binder, auxiliaries, toughening agents and an active metal salt aqueous solution, then extruded directly into shape. The shorter flow cuts cost and eases industrial application. In catalytic ozone oxidation reactions the resulting catalyst effectively promotes ozone decomposition and raises the ozone concentration in the liquid phase, accelerating the oxidation reaction rate.
Compared with virgin catalyst manufacture, the spent-catalyst route starts partway up the value chain: the carrier is already shaped, calcined and proven porous. The preparation work therefore concentrates on loading fresh active metal onto a skeleton that would otherwise be discarded, and the energy embedded in that skeleton comes free. That is the structural reason a recovered catalyst can undercut a virgin one on cost while matching it on the metrics that matter, mechanical strength and activity.
Why this matters beyond the refinery fence
The resource utilization of FCC spent catalysts solves a waste disposal problem and simultaneously supplies efficient, low-cost catalysts for environmental protection. Catalyst makers such as SINOKLE, whose product lines centre on heterogeneous ozone catalysts, watch this feedstock route closely, since cheaper raw material streams translate directly into lower catalyst cost per cubic metre of treated water. Water treatment is only the first field: air purification and other oxidation duties are natural extensions.
The trajectory depends on two variables, both still moving. Preparation processes continue to be optimised, and catalyst performance keeps improving as the metal loading recipes mature. As both advance, ozone catalysts converted from spent catalysts will take a larger share of the environmental materials market, contributing to the green transformation and sustainable development of the petrochemical industry. It is a rare case in industrial ecology where a disposal liability becomes the product itself.