Home News Knowledges Reinjection Water Standards Are Tightening: Two Process Schemes That Meet A1 and A2 Without Chemicals

Reinjection Water Standards Are Tightening: Two Process Schemes That Meet A1 and A2 Without Chemicals

2026-11-16 5 readings

As national environmental standards keep tightening, oilfields are moving towards total pollutant control and compliant reinjection. Faced with increasingly strict rules, water treatment systems must run continuously and stably, ensure compliant discharge and eliminate any risk of leakage. At the same time, as fields enter mid-to-late life the water cut of produced fluid keeps rising, placing higher demands on the efficiency, compactness and stability of treatment equipment. Current produced water systems, however, generally suffer from weak shock resistance, fluctuating performance and complex operation and maintenance, which constrains further oilfield development. Reinjection water treatment has therefore become an urgent need in oilfield produced water management.

Conventional Technologies and Their Limits

Previous reinjection water processes show clear shortcomings. Inclined plates with walnut shell or fibre-ball filtration are permeable, but chemical dosing and aged oil reduce system reliability and shock resistance, making effluent quality hard to keep stable. Combinations of settling tanks with centripetal flotation, fibre-ball or multimedia filters and ceramic membranes involve complex flows, high energy demand and high operating cost, and also suffer poor shock resistance and marked effluent fluctuation. Processes using settling tanks with centripetal flotation, fibre-ball or multimedia filters and ultrafiltration membranes struggle in high-temperature environments; membrane materials adapt poorly to crude oil, long-term stability is insufficient, and high salinity adds to the difficulty and cost of operation and maintenance.

The SINOKLE Reinjection Water Route

The new-generation reinjection water process from SINOKLE centres on cyclonic dissolved-air flotation and integrates an HAC cyclone separator, high-precision active filters and SiC microfiltration membranes into an integrated solution for oilfield produced water. The process achieves short-flow treatment of produced fluid without chemical agents, runs stably, meets reinjection standards, produces skimmed oil with low water content and allows the solids to be filter-pressed and safely transported off site.

Two Schemes for Two Standards

SINOKLE has designed two process schemes to suit different project conditions, processes and treatment difficulties, meeting produced water standards A1 and A2 respectively.

  • Scheme 1: two-stage HAC + two-stage CDFU + two-stage KFM filters, achieving the A2 standard.
  • Scheme 2: two-stage HAC + two-stage CDFU + SiC membrane filter + CDFU, achieving the A1 standard.

Features of the Process

  • Mature process with strong shock resistance and stable, reliable performance.
  • Purely physical demulsification: no chemicals, no aged oil, no secondary pollution, with good environmental benefits.
  • Short process flow, small footprint, few operating units, simple operation and relatively low operating cost.
  • Two-stage cyclonic oil-water separators and two-stage cyclonic dissolved-air flotation make downstream treatment more stable and reliable.
  • Advanced filtration technology ensures stably compliant water quality.

Why the Front End Is Always Two-Stage

Every scheme above doubles the same two components, and the duplication is deliberate. Rising water cut means the front end sees volumes that swing with well callbacks, and a single HAC cyclone stage would pass its overload straight into flotation; two stages in series absorb the swing between them. The same logic applies to the CDFU pair: the first stage takes the bulk oil and the flow shock, the second polishes to reinjection quality even when the first was pushed beyond its comfortable envelope. Fields running this configuration report that downstream filtration changes out less often, because the load arriving at that step is both smaller and more consistent.

The HAC cyclone separator itself earns its place at the head of the train. It handles the grit and free oil that would otherwise reach the flotation stage, and it does so without chemicals, which is what keeps the whole route inside the purely physical envelope that aged-oil-laden streams require. It also keeps the reinjection water clean of surfactant residue, so formation behaviour downstream of the wellbore stays predictable.

What Chemical-Free Operation Changes for the Field

Removing chemicals from the produced water train sounds like a slogan until its consequences are itemised. No demulsifier means no aged oil accumulating in the skimmed-oil route, so that oil returns to the processing train with low water content instead of being re-treated. No coagulant means no chemical sludge to filter-press and haul; the solids that do leave site are formation solids, filter-pressed and transportable. No flocculant means the flotation stages cannot be blinded by overdosing during an upset, so recovery from a shock load is a matter of waiting rather than of re-tuning chemistry. Each item alone is a convenience; together they change the operating economics of the water side, which is why the two schemes hold their performance without the operator interventions conventional trains require.

Choosing Between the Schemes

The choice between Scheme 1 and Scheme 2 is really a choice about what the receiving system demands. Where the reinjection target is the A2 standard, the two-stage KFM filtration train closes the loop with proven, mechanically simple hardware. Where A1 applies and finer solids control is required, the SiC membrane filter slot takes over the polishing duty, with a final CDFU stage protecting the membrane from oil creep. Both schemes share the same front end, so a field can start with Scheme 1 hardware and extend towards A1 without discarding what it has already built.

These schemes not only bring discharge quality up to national standards but also help raise oilfield production efficiency and overall economic performance, which is ultimately what keeps reinjection compliance sustainable over the life of the field.