Home News Knowledges Why Produced Water Quality Makes or Breaks Waterflood Performance in Low-Permeability Reservoirs

Why Produced Water Quality Makes or Breaks Waterflood Performance in Low-Permeability Reservoirs

2026-11-20 11 readings

Produced water arrives at the surface as a complicated multiphase system: suspended solids, oil, dissolved gases and dissolved salts travel up the wellbore together with the crude, then pass through demulsification and separation. Its impurities fall into five categories — suspended solids, colloidal particles, dispersed and floating oil, emulsified oil and dissolved substances — and every downstream decision, from equipment sizing to reinjection compliance, traces back to how well those five are handled.

Two Treatment Philosophies

In China's oilfield oily wastewater practice there are two main approaches. Conventional treatment, the usual choice for high-permeability reservoirs, combines sedimentation de-oiling with single- or dual-media filtration. Low-permeability reservoirs demand more: conventional treatment is followed by advanced treatment, mainly two- or three-stage filtration, to reach higher standards.

De-oiling is the key step and covers four families — gravity, pressure, flotation and hydrocyclone de-oiling — while filtration relies mostly on single- or dual-media beds. Reinjecting water that meets standard pays off three ways: it effectively inhibits clay mineral swelling and greatly reduces potential formation damage, it lowers the risk of environmental pollution, and it saves fresh water with significant economic and environmental benefits. Adopting advanced, efficient produced water treatment technology is therefore not a nice-to-have but an essential and indispensable task for oilfield development and sustainable operation.

The Tuha Lesson: What Substandard Water Actually Costs

Most developed blocks in the Tuha Oilfield are low-porosity, low-permeability reservoirs with multi-layer, strongly heterogeneous formations and pronounced water sensitivity, salt sensitivity and velocity sensitivity. Given those conditions the field sets strict injection water quality standards, because substandard water injected into the formation cuts its intake capacity and undermines waterflood performance and normal injection development.

Where injection capacity cannot balance production, formation pressure is held low and production capacity cannot be maximised. The deterioration mechanism is gradual but relentless: during treatment and reinjection, suspended solids, corrosion products and bacteria ride along with the water, plugging pore throats and reducing the intake of injection wells until some fall into under-injection. Once dissolved oxygen, bacteria or carbon dioxide in the injected water exceed the standard, the water grows more corrosive, and corrosion of water treatment equipment shows up mainly as perforation at weld joints.

Four De-Oiling Technologies Compared

Waterflooding supplements formation energy and keeps reservoir energy in stable balance so the field can sustain high, stable production — but injecting untreated wastewater damages the reservoir, as prolific bacteria, mechanical impurities and iron precipitates plug it, raising injection pressure, lowering injection volume and seriously impairing displacement efficiency. Since the water comes from the reservoir itself, treatment for reinjection focuses on oil removal and suspended solids removal in two stages: de-oiling, which uses the density difference between oil and water together with demulsification and flocculation, and filtration, which relies on the adsorption and interception of the filter media to hold impurities on the surface or block them from passing through the bed. The de-oiling stage must be matched to the density and pour point of the crude in the oily water.

  • Gravity separator tank. Larger oil droplets rise naturally under buoyancy while emulsified oil coalesces from small droplets into large ones under the action of a demulsifier or coagulant; after a certain retention time most of the crude rises to the top of the tank and is removed. The tank is large and the retention time long, so sudden changes in influent flow or quality do not significantly affect effluent quality — but the footprint is large and the removal of emulsified oil is limited.
  • Pressure sedimentation. Coalescing material packed inside the equipment lets fine droplets merge into larger ones as oily water passes the coalescing bed, speeding oil rise, shortening retention time and reducing equipment size; coalescing inclined plates markedly improve de-oiling efficiency, though adaptation to influent swings is weaker than a separator tank.
  • Flotation de-oiling. Large numbers of fine bubbles are generated in the oily water, and suspended oil droplets 0.25-25 μm in size and solid particles attach to the bubbles and rise to the surface, removing oily sludge and suspended solids. Flotation markedly increases droplet rise velocity and shortens treatment time; it handles large volumes with high efficiency and suits heavy-oil fields and oily water with a high emulsified oil content.
  • Hydrocyclone de-oiling. High-speed spinning separates oil from water through unequal centrifugal forces acting on their density difference. The equipment is compact with high separation efficiency, but it adapts poorly to oily water whose crude relative density exceeds 0.9.

CDFU: Cyclonic Flotation Enters the Field

Continuous innovation in produced water treatment has yielded many new technologies with high efficiency, good quality and high reliability, and the SINOKLE contribution is a first-of-its-kind-in-China compact enclosed pressurised flotation technology: cyclonic dissolved gas flotation, deployed as the CDFU (Cyclonic Dissolved Gas Flotation Unit), which combines cyclonic separation with a new generation of micro-bubble generation and dissolved gas flotation technology.

Field data backs the concept. In 2018, two CDFU units were used at the Tuha Oilfield to treat produced water: with influent oil ≤1,000 mg/L and suspended solids ≤500 mg/L, the effluent reached oil ≤10 mg/L and suspended solids ≤10 mg/L — an oil removal rate of 99% and a suspended solids removal rate of 98%.

For operators of low-permeability blocks, the message from the Tuha experience is straightforward: the treatment train is part of the reservoir engineering package, not a bolt-on utility. Pick de-oiling technology that tolerates the field's crude properties, hold suspended solids and oil at or below the numbers the formation can accept, and the injection system — and the waterflood economics that depend on it — stays healthy.