Home News Knowledges Heavy Oil Tank Farm Wastewater: Why Gravity Separators Stall and What Two-Stage CDFU With KFM Delivers

Heavy Oil Tank Farm Wastewater: Why Gravity Separators Stall and What Two-Stage CDFU With KFM Delivers

2026-11-19 2 readings

In the petrochemical industry, oily wastewater from heavy oil tank farms is a special industrial wastewater whose treatment has always been a technical challenge. Storage, loading and transport of heavy oil inevitably generate large volumes of oily wastewater carrying high concentrations of petroleum substances together with suspended solids, silt and dissolved impurities. The composition is extremely complex, and it poses a potential threat to the environment and ecosystems if it leaves the fence untreated.

What Makes This Wastewater Different

In short, it is wastewater containing large amounts of oil generated during the operation of a heavy oil tank farm. The oil comes mainly from leakage, evaporation and washing of products, and it mixes with rainwater and washdown water across the tank area. Heavy oil is highly viscous, dense and hard to emulsify, which sounds like good news for separation until the whole picture is considered: the same viscosity that keeps droplets from dispersing finely also keeps them from rising quickly, and the density gap between heavy oil and water is narrower than the textbook assumes.

The Difficulties, Stated Plainly

The oil in this wastewater is mainly heavy oil, highly viscous and dense, with a high content of suspended solids of varying particle size. First, the high viscosity of heavy oil defeats conventional oil-water separation, so oil cannot be separated effectively by the methods that work on lighter crudes. Second, the complex composition readily causes secondary pollution during treatment, which further raises both difficulty and cost. Add silt that settles into every dead zone and dissolved impurities that no mechanical stage touches, and the stream earns its reputation.

Conventional Equipment and Where It Stops

Conventional treatment relies on gravity oil separators, flotation and filtration. Gravity separators exploit the density difference between oil and water but remove only most free oil, with limited effect on emulsified and dissolved oil. Flotation removes some emulsified oil but performs poorly on heavy oil and is sensitive to water quality fluctuations, which tank farms deliver in abundance during washdown and loading events. Filtration clogs readily when treating water with high suspended solids, requiring frequent media replacement and high operating cost. Stacked together, these shortcomings make it hard to meet discharge standards reliably, and the operators end up dosing more chemicals or sending more water back around the loop.

The Two-Stage CDFU Plus KFM Process

To address these difficulties, SINOKLE has combined its core patented CDFU and KFM equipment into a new treatment process. The process uses two stages of CDFU cyclone dissolved-gas flotation for oil and suspended-solids removal: cyclone and dissolved-gas technology bring micro bubbles into full contact with, and attachment to, oil droplets and solids for efficient separation. The cyclonic field does the work gravity cannot, spinning the dense droplets into contact with a bubble swarm that carries them out regardless of how slowly they would have risen on their own. After two stages, most oil and suspended solids are gone. The water then passes through a KFM active filter media filter for advanced treatment, removing the remaining pollutants and ensuring compliant discharge at the outfall.

Features Worth Listing

  • Purely physical separation avoids the secondary pollution of chemical agents, giving a stable, reliable process with high oil removal efficiency.
  • The process is stable, the equipment compact and the footprint small, suiting space-limited heavy oil tank farms.
  • Equipment runs fully enclosed, eliminating waste gas leakage for greater environmental protection.
  • Skid-mounted, automated design makes operation and maintenance simple, shortens construction and allows online implementation.
  • High shock resistance tolerates wide water-quality fluctuations, so washdown events do not derail the effluent.

The Numbers From the Field

The process has been applied in the wastewater treatment project of a heavy oil tank farm at a petrochemical company. Influent petroleum content ran as high as 10,000 mg/L with 500 mg/L of suspended solids. After treatment, effluent petroleum fell below 10 mg/L and suspended solids below 20 mg/L, and the outfall met discharge standards consistently. A removal of better than 99.9% on petroleum, delivered by two flotation stages and one media filter with no chemical sludge to dispose of, changes how a tank farm budgets its water: the treatment cell stops being a cost center that occasionally embarrasses the site and becomes just another steady utility.

Selection Notes for Other Sites

For operators weighing options, three checks matter before committing. Confirm what the separator stage actually receives, because tank farm effluent swings between quiet rainwater runs and washdown surges, and the first CDFU stage must absorb both. Look at where the oil ends up, since a purely physical process concentrates pollutant into a compact heavy phase rather than spreading it through a chemical sludge that needs handling. And check the enclosure: tank farms sit next to product storage, so a sealed unit that vents nothing beats an open basin that trades a water problem for an air problem. Where those three checks point toward flotation, the two-stage CDFU plus KFM arrangement is the configuration to price.