Atmospheric Overhead Sour Water: Where the Emulsion Comes From and How to Deoil It Before Stripping
Crude oil processing first splits the crude into straight-run fractions by boiling point, then removes the non-ideal components from those fractions or converts them by chemical reaction into the required components. Distillation remains the most common and economical separation method, and it is the first processing step every crude takes in a refinery, which makes the water drawn off the column tops one of the most predictable waste streams in the plant.
Where the Oil in the Water Comes From
Through atmospheric and vacuum distillation the crude separates into fractions, the overhead oil vapor is condensed, and oil, water and gas separate in the oil-water separator. Because that condensed wastewater usually carries high concentrations of sulfides, it is known as sulfurous, or sour, wastewater, and after steam stripping it normally returns to downstream units as purified water for reuse. In recent years, though, crude slates have grown poorer in quality and more diverse, and the atmospheric and vacuum overhead condensate now emulsifies and carries oil far more often than it used to. The consequences reach well beyond a light-oil yield loss.
What Carried Oil Does to Downstream Units
Oil acts as a surfactant once it reaches the stripping column. Under the intense gas-water contact there, it foams readily, and large amounts of foam prevent effective mass transfer between the gas and liquid phases. Steam consumption climbs, operation fluctuates, and column capacity drops. Emulsified oil is also complex in composition: when oil content runs high it accumulates and plugs key locations such as trays and reboilers, cutting mass-transfer efficiency, risking local overheating and shaving both equipment performance and service life. By-product quality suffers too, because hydrocarbons in the sour water produce black sulfur during stripping, and oil carried in liquid ammonia contaminates the product.
Why the Emulsion Holds Together
The stability has a physical chemistry explanation. Inferior heavy oils contain natural surfactants, chiefly asphaltenes, resins and petroleum acids. Production chemicals added during extraction, such as alkylbenzene sulfonates and fatty-alcohol polyoxyethylene ethers, plus corrosion inhibitors added during distillation, form anionic surfactants. These molecules are weakly hydrated and enter directly into the inner Helmholtz plane, replacing the water-dipole layer and adsorbing specifically on oil-droplet surfaces, which lowers the oil-water interfacial tension. The negative charges on the droplet surface and the anionic surfactants together form a Stern electric double layer, producing a zeta potential. Because the liquid temperature is high, diffusion is pronounced: the thicker the Stern double layer, the higher the zeta potential and the greater the repulsive force between droplets. Oriented adsorption at the oil-water interface then builds a stable, robust interfacial film that prevents coalescence when droplets collide. That is why these oil-in-water emulsions stay stable, refuse to separate even after long settling, and carry a high oil load into every downstream unit.
Deoiling Before the Column
To guarantee the efficiency and stability of stripping, the oil must be removed before the sour water enters the stripping column, generally to below 50 mg/L. Among the deoiling technologies used across refineries, coalescence, sometimes called coarse-graining, attracts particular attention for four reasons: small footprint, low equipment cost, no chemical dosing and therefore no secondary pollution, and low energy consumption at large treatment capacity.
The method itself is straightforward. Coalescing material is packed into a device through which the oily wastewater flows, and the immiscible dispersed oil droplets and water particles coalesce separately, enlarging particle size. The principle rests on the different affinities of the oil and water phases for the coalescing material. Small oil droplets are intercepted by the media, hold on its surface and inside its pores, and grow into larger oil films or droplets; under buoyancy and hydraulic forces they then detach from the coalescing surfaces, overcome the flow resistance and rise faster, achieving oil-water separation without adding a single chemical to the stream.
Where Coalescing Fits in the Train
Coalescing works best on dispersed oil, the size range between free oil that separates by gravity and the chemically stabilised emulsion that resists everything short of chemical or electrochemical treatment. For atmospheric overhead sour water, whose droplets are small but not yet fully locked into a Stern-layer-protected emulsion, a coalescing stage ahead of stripping removes most of the oil load at modest cost and leaves the fine polishing to whatever stage follows. The operating boundaries matter too: high suspended solids blind the media, so a filtration step ahead of the coalescer keeps the surface open, and temperature helps rather than hurts, since warmer water lowers viscosity and lets droplets rise free more readily. Plants that skip pretreatment pay for it later in tray fouling, reboiler cleaning and off-spec sulfur, all costs that dwarf the price of the deoiling package itself.
Field Record
SINOKLE has accumulated extensive experimental exploration and industrial application experience in deoiling. In 2021, at a PetroChina refinery in Chad, a combined filtration plus coalescing deoiling process was adopted for sulfurous wastewater pretreatment at 20 m³/h. The influent oil concentration sat at 500 mg/L, and the effluent left below 15 mg/L, an oil-removal efficiency greater than 97%. For a stream that used to ship foam, plugged trays and contaminated ammonia downstream, that single pretreatment step quietly protects the entire stripping train, and the coalescing stage doing the work has no chemicals to replenish and very little to maintain.