Home News Knowledges Cooling Tower Selection: Counterflow, Crossflow, Closed-Circuit Units and the Fan Controls Behind Them

Cooling Tower Selection: Counterflow, Crossflow, Closed-Circuit Units and the Fan Controls Behind Them

2026-11-19 3 readings

Cooling water quality is never the product of a single knob. Temperature approach, circulation rate, evaporation, drift, blowdown and makeup chemistry all interact, which is why cooling towers have collected decades of incremental engineering rather than one decisive redesign. Choosing the right tower family and then controlling its fans properly still delivers more value than any device bolted onto a badly selected unit.

What the Tower Does and Where It Serves

A cooling tower rejects process heat by exposing warm water to moving air, letting a fraction evaporate and returning the cooled water to the process. The installed base spreads across air-conditioning cooling systems, refrigeration plants, injection molding, leather making, foaming, power generation, steam turbines, aluminum profile processing, air compressors and general industrial water cooling, with the densest capacity in air-conditioning cooling, refrigeration, plastics and chemical production. Manufacturing users include food plants, pharmaceuticals, metal casting, rubber, textiles, steel mills and petrochemical products.

Five Terms Every Operator Should Know

Drift

Drift means the fine droplets carried out of the tower with the hot, moist exhaust air, and their impurity load matches the circulating water entering the tower. Drift eliminators, often simple baffle assemblies, sit after the fill and spraying zone and strip the droplets before the air leaves the casing.

Windage

Windage, sometimes called splash-out, is water blown or splashed out near the air inlet, and strong wind adds to it. Wind screens, louvers and splash deflector plates contain the loss.

Plume

The plume is the visible white cloud outside the stack: saturated moist air leaves the tower top, meets colder ambient air, and its vapor condenses into fine droplets.

Noise and hygiene

Noise is the sound energy radiated to the surroundings, measurable at a set distance and direction. Aerodynamic noise from rotating fan blades dominates, backed by mechanical noise from the motor, gearbox and drive belts. Long-running towers also grow bacteria, and the notorious species is Legionella, which can cause infectious disease and reaches an area of about 800 meters around every cooling tower, so tower hygiene matters well beyond water chemistry.

Counterflow Versus Crossflow

In a counterflow tower, water falls through the fill while air enters horizontally, so the two streams cross at right angles. This is the configuration most used in noise-sensitive districts and the most common choice in air-conditioning service. Its advantages are practical: energy saving, low water pressure, low air resistance, suitability for low-speed motors, no dripping noise complaints, and convenient access to the fill and water distribution system. Between the fill and the collecting basin, falling droplets cool the water a little further, the so-called tail effect, which lowers outlet temperature by 1-2 °C in northern China. Added up, a counterflow tower needs roughly 20% less fill volume than an equivalent crossflow unit, so cooling efficiency comes out higher.

The crossflow layout trades those strengths for others. Its frame consumes about 40% more material, heat exchange demands a larger fill volume, the fill ages faster, water distribution holes clog easily, freeze protection is weaker, and wet-air recirculation runs higher. Each design's advantage is the other's disadvantage, which is why both remain in production. On the operational side, counterflow water distribution rarely blocks, the fill stays clean and ages slowly, and freeze-protection measures are easier to implement. Multiple counterflow units also combine flexibly in winter, with fans stoppable entirely to hold the required temperature and flow.

Spray-Filled and Closed-Circuit Designs

Spray, or fill-free, towers mount special nozzles at the upper air inlet at the tower bottom, with either fan-free self-rotating spray supply or top exhaust. Hot water passes swirl vanes inside the nozzle and atomizes into fine mist that cools in two stages, upward co-current spraying and downward counterflow falling. Atomization stays uniform without hollow cones, the cooling effect is stable, power draw is low, and the drift rate measures just 0.01%. With no fill to buy or replace, cost drops and service life lengthens, and the design complies with national standard GB7190.1-1997.

A closed-circuit cooling tower, also marketed as an evaporative air cooler, places a tubular heat exchanger inside the casing and cools through three-way exchange among flowing air, spray water and the circulating water itself. Because the process loop stays sealed, water quality is protected and the main equipment lasts longer, and when ambient temperature drops the spray system can shut off to save water. These towers now serve steel and metallurgy, power and electronics, machining and air conditioning. Northern winters push freeze protection to the top of the agenda: tubes can split if water freezes inside, so every duty pattern needs a drainage plan whenever the unit shuts down.

Fan Control: Where the Energy Actually Goes

Fan energy-saving management aims at closed-loop automatic control: preset the supply water temperature from production needs, let temperature sensors feed back climate and heat-transfer changes, and trim cooling equipment energy to hold the setpoint. Variable-frequency speed regulation, abbreviated VFD, is generally treated as the ideal tool, yet on circulating-water tower fans it carries three known defects. The frequency converter itself loses energy, with average operating efficiency below 90%, which eats into the savings. The design must guard against destructive resonance at particular converter speeds and against strong electromagnetic interference reaching other instruments. And on high-power systems with few large fans, starting or stopping one fan swings the water temperature so far that controllers struggle to stabilize it.

Fan safety monitoring covers the other half: detecting vibration, oil temperature and oil level changes automatically, and alarming or shutting down fans whose values exceed limits. The combined probe mounts on the fixed seat of the gearbox oil dipstick with its rod dipped in the lubricating oil, converting oil temperature, level and vibration into electrical signals sent to the control room monitor, and one monitor serves several probes with digital display, over-limit alarm and shutdown. Monitors network to a management computer through a four-core RS-422 standard serial cable. The weak point remains oil-level sensing, where hot-wire scaling or breakage still forces periodic manual inspection.

Water Losses, Makeup and Blowdown

What evaporates during cooling is relatively pure water, while drift removes only a small proportion of the volume. Because the same water circulates repeatedly, dissolved solids concentrate, quality deteriorates and algae take hold, so part of the flow must be blown down and replaced. For air-conditioning duty, designed around a 5 °C temperature range, makeup runs about 2% of the circulating volume, drift loss lands near 0.1-0.2%, and blowdown, governed by dissolved solids, generally runs about 0.3%.

Scale, Corrosion and the Coating Program

Most cooling water carries calcium and magnesium ions with acid carbonates, which deposit on metal surfaces, while dissolved oxygen corrodes the same surfaces into rust. Deposits throttle heat transfer until, in bad cases, tubes block and heat exchange stops. Research data attribute a severe energy penalty to scale: even a very thin layer raises the operating cost of the scaled section by more than 40%. Mechanical scraping, high-pressure water and acid pickling each disappoint, because deposits survive, acid attacks the metal and forms holes, and residual acid drives under-deposit corrosion until replacement. A cleaning agent with low metal corrosivity, high efficiency and environmental safety keeps channels clear without those side effects.

Surface protection follows a fixed sequence. Within 6 hours of surface acceptance, brush the prepared epoxy primer after wiping the tower down with gasoline-soaked cotton yarn; it must go on uniform, without sagging, pinholes or bubbles, at 25-35 µm film with 80-90 g/m² dosage and an extra pass on corners. The second epoxy coal-tar glass-flake primer follows at 35-40 µm after natural cure, then the intermediate glass-flake paint at 110-125 g/m² per coat and 45 µm film, then top coats at 40-50 µm and a final 80-100 µm pass.

Materials, Maintenance and Thermal Checks

Routine care is mostly oil discipline: check the gearbox level often, run No. 22-28 hypoid gear oil or No. 90-120 industrial gear oil, changing the oil after the first 500 hours, with the higher-viscosity grade in summer. Wire the motor strictly to the supplier's diagram and start from low speed, and if high-speed current exceeds rated after the blade angles are set to catalog values, stop and readjust. The adjustment standard marks each blade 150 mm from the casing, keeps the height difference spread within 2 mm, and targets high-speed motor current at 0.9-0.95 of rated. FRP is combustible, so open flames are banned during maintenance. Thermal performance, noise and vibration indicators fall under the design responsibility of the Fourth Design and Research Institute of the Ministry of Machinery Industry, with the tower supplier answering for product quality.

Thermal calculation determines tower area from water and heat loads under specified meteorology, or predicts cooled water temperature from tower parameters. Mechanical-draft towers are sized with the Merkel enthalpy-difference method or graphical methods, and packaged units are checked straight from catalog charts. Fill hardware rounds out the selection: PVC inclined-corrugated fill in 125, 200, 230, 250 and 300 sizes, plus square-tower fill panels of 1000 mm × 500 mm and 1200 mm × 500 mm.