Desalter Effluent Carrying Over 20% Oil: A Two-Step Train Built for Density-Difference Failure
With crude oil sources becoming more diversified and quality becoming heavier and poorer, refineries often blend recovered heavy dirty oil into the mixed feed. Although this raises utilization, it causes severe crude oil emulsification and greatly impacts the electric desalting unit. Equipment aging, overload and improper operation often lead to poor demulsification and unstable interface levels, resulting in excessive oil in the effluent, which impacts downstream wastewater treatment and wastes crude oil at the same time.
Why Desalting Wastewater Is So Hard to Treat
The characteristics of the stream make it extremely difficult. Heavy oil content is high, with a density close to that of the wastewater itself, which makes separation difficult. Oil content exceeds 20%, with fine, severely emulsified oil droplets. Large amounts of fine suspended solids aggravate emulsification and corrode and clog equipment. High salinity and high mineralization accelerate corrosion and scaling, and dangerous gases such as sulfides and volatile phenols threaten health and the environment.
Where Existing Technologies Fall Short
Traditional gravity settling gives unstable results. Cyclonic centrifugal separation has higher efficiency but high energy consumption and requires chemicals. The requirements themselves are punishing: the high and volatile oil content demands strong shock resistance; severe emulsification makes physical demulsification the core technical bottleneck, since chemical methods are unreliable; the oil and water densities are close, so separation by density difference alone performs poorly; and strong corrosion, easy scaling and grit content require strong anti-clogging and desanding capability.
The New Two-Step Process
SINOKLE developed a new high-efficiency process that answers these difficulties in two steps.
Step one, preliminary separation. After heat exchange and cooling, the oily wastewater enters the high-efficiency coalescing oil-water separator. Floating oil, dispersed oil and part of the emulsified oil quickly gather and coalesce into large oil masses, which separate into the oil collection pocket.
Step two, advanced demulsification and oil removal. The wastewater after preliminary separation, still containing large amounts of emulsified oil, enters the high-efficiency cyclonic dissolved air flotation unit, the CDFU. The emulsified oil is captured by ultrafine bubbles, and under the cyclonic action it gathers, coalesces, demulsifies and forms oil masses that separate out. The treated wastewater, with oil content <100 mg/L, is discharged into the sewage treatment plant pipe network.
Corrosion, Scaling and the Salinity Problem
Salinity deserves its own discussion because it attacks the equipment as well as the process. High mineralization drives scaling on warm surfaces and accelerates corrosion across the train, while sulfides and volatile phenols make any open handling of the stream a personnel hazard. The two-step route responds structurally rather than chemically: coalescence and flotation both proceed in sealed vessels, so the dangerous gases never find an escape path; the working pressure stays low, which keeps vessel wall requirements moderate even where chloride load is punishing; and because the separation relies on bubble capture and coalescence rather than on consumable media, there is no filter cake or ion-exchange bed quietly concentrating corrosive species. Anti-clogging and desanding provisions in the internals handle the fine suspended solids that would otherwise bed in anywhere velocity drops. The outcome is a train that tolerates the stream's chemistry instead of being consumed by it. Desalters that feed this route also see a side benefit: with effluent oil held below 100 mg/L, the biological units downstream no longer receive oil shocks, and their own stability improves measurably.
Core Advantages of the Route
- Innovative separation mechanism: breaking through the limitation of relying solely on the oil-water density difference, it comprehensively utilizes the gas-water and oil-gas-water density differences. The oil removal effect is basically unaffected by the density of the dirty oil, and efficiency is greatly improved.
- High efficiency and stability: using a high-efficiency coalescing/inclined-plate pressure oil remover together with the compact CDFU, it offers high separation efficiency, strong shock resistance, clog resistance and low energy consumption, with a working pressure of <0.15 MPa.
- Reliable operation: even with drastic fluctuations in influent oil content, the effluent quality remains consistently stable and compliant, with oil below 100 mg/L.
- Automation and safety: fully enclosed automatic control reduces labor and maintenance costs, prevents the leakage of dangerous gases, and safeguards personnel health and environmental safety.
- Economic efficiency: the equipment offers high cost performance, bringing significant economic and social benefits to the enterprise.
The Design Logic in One Paragraph
The train is sequenced around the failure modes of the stream. Coalescence comes first because it needs only partial demulsification to strip the free and dispersed fractions cheaply. The CDFU comes second because cyclonic capture by ultrafine bubbles works precisely where density difference fails, on the fine emulsified droplets that gravity cannot see. Sealing the whole train under low pressure keeps sulfides and volatile phenols contained. What emerges is a desalting wastewater route whose effluent holds below 100 mg/L regardless of how the desalter above it misbehaves.
For the refinery as a whole the sequencing also protects crude economics: less oil escaping into the wastewater drain means more heavy dirty oil staying in the product stream, which is where the blending decision intended it to end up.