Home News Knowledges Ship and Port Oily Water: A Purely Physical Route That Skips Flocculants

Ship and Port Oily Water: A Purely Physical Route That Skips Flocculants

2026-11-16 5 readings

Ship, port and terminal oily water is the wastewater containing grease, fuel residues and lubricating oils generated during ship operation. Its sources concentrate in two places: engine rooms and cargo holds. The stream gathers oily tank washing water, engine-room oily water and oily ballast water, and its main components tell the story of where it comes from: fuel combustion residues such as unburnt hydrocarbons and solid particles, various lubricating oils including main engine oil and gearbox oil, oils and greases from processing, storage and transport such as edible oil, paraffin and paint, plus oily washing water and domestic sewage.

Why This Stream Resists Ordinary Treatment

Two properties make the wastewater awkward. First, it is heavily emulsified, so conventional oil separation and gravity settling struggle to break it. Second, the obvious alternative, chemical dosing, generates large amounts of hazardous waste at high cost, which shifts the problem rather than solving it.

The CDFU Answer: Demulsification Without Chemistry

To tackle this problem, a technical scheme centred on the CDFU cyclonic dissolved gas flotation unit is adopted. The technology efficiently demulsifies and removes oil by purely physical means, achieving stable, compliant treatment and discharge of the oily water. In construction it organically integrates cyclonic centrifugal separation, a new generation of dissolved air technology and high-efficiency flotation separation. Using micro-nano bubbles generated by cyclonic action and dissolved gas, together with a specially designed flotation mode, it markedly raises flotation efficiency and shortens retention time, achieving rapid, efficient removal of oil and suspended solids.

Core Advantages of the Process

  • Purely physical demulsification: efficient oil removal, stable and reliable; the recovered oil is reused, with no secondary pollution and no hazardous oily sludge, combining environmental and economic benefits.
  • Waste reduction and cost saving: scum volume is reduced by more than 1/3, less hazardous waste is generated, and secondary treatment costs stay low.
  • Safe and environmentally friendly: closed pressurised operation prevents hydrogen sulphide and oil vapour leakage, keeping the site environment friendly.
  • Efficient and compact: single-stage retention time is under 5 minutes with a small footprint; operation is fully automatic, O&M is easy, the construction period is short, and online implementation is supported.
  • Stable and reliable: strong shock resistance tolerates large fluctuations in water quality.

How the Two-Stage Flow Actually Runs

The oily water undergoes two-stage CDFU treatment. Inside the tank, cyclonic action lets ultra-fine bubbles generated from dissolved air attach rapidly to the oil, which demulsifies, aggregates and floats up, discharging through the top oil outlet.

Under the normal operating condition no flocculant is dosed in either stage: discharged oil goes to the waste oil tank and residue to the sludge pit. Under a highly emulsified condition the first stage still runs without flocculant, and a small amount of flocculant is added to the second stage as needed, with the same discharge routing. The second-stage CDFU effluent is checked by an oil-in-water analyser and enters downstream processes once compliant. Nitrogen serves as the inlet gas in both stages, and the tail gas is treated by a tail-gas destructor before discharge. The treated effluent stably meets the standard.

System Control

Operation is fully automatic and closed under pressure, with no safety or environmental risk. CDFU effluent, discharged oil, exhaust, gas make-up and dissolved-air system intake are all automatically controlled. The dissolved air pump has automatic and manual start modes together with automatic protection programs. The skid uses PLC/DCS fully automatic control, which keeps operation and maintenance simple.

What Purely Physical Treatment Buys at the Compliance End

The phrase purely physical is not marketing shorthand here; it has measurable consequences downstream. With no demulsification chemistry in the normal flow path, there is no emulsion-breaking polymer to dispose of, and the scum that leaves the top outlet is recoverable oil rather than a chemical-oil mixture. Hazardous waste manifests shrink accordingly, and the tail-gas destructor closes the last open path by treating nitrogen-borne emissions before release. Because every stage runs inside a closed pressurised vessel, the hydrogen sulphide and oil vapour that make engine-room drainage unpleasant stay contained from inlet to discharge, and the operator's exposure to them ends at the sample point. For a terminal, that containment also simplifies permit discussions, because the emission inventory is short and each item has an engineered control attached.

A Port Project in Guangdong

One application illustrates the scale. A port project in Guangdong treats 60 m³/h with a single skid containing two CDFU reaction tanks and one stabilisation tank, occupying only about 30 m². Influent oil content is about 1000 mg/L and suspended solids about 1000 mg/L. After two-stage CDFU treatment the oil content drops below 30 mg/L and suspended solids below 60 mg/L, followed by further treatment to achieve compliant discharge.

For terminals balancing discharge limits against hazardous waste fees, the arithmetic is persuasive: a purely physical demulsification step that reuses recovered oil, avoids oily sludge, and holds effluent stable through quality swings converts a recurring liability into a manageable utility line item.