Reading Activated Sludge: SV, MLSS and SVI as a Diagnostic Set
What activated really means
Activated sludge is a flocculent biomass with strong adsorption and degradation capability, and its essence is that it is alive. Rivers purify themselves because microorganisms living in the water consume pollutants; that living community is the activated part. Microorganisms are only a fraction of the sludge, though. It also contains the residues of microbial metabolism and the organic and inorganic matter adsorbed onto the flocs. The mixed liquor seen in an aeration tank is simply activated sludge suspended in water.
Zoogloea and filamentous organisms: a see-saw
Zoogloea-forming and filamentous bacteria are the two structural components. Zoogloea are aggregates of floc-forming bacteria with slime or capsules; they adsorb impurities and free microorganisms, give the sludge good settleability, and shelter microfauna from being swallowed or poisoned. Filamentous organisms are the skeleton: growing on the zoogloea framework, they let flocs form larger particles while keeping the sludge porous.
The two stand in a see-saw relationship. Filamentous organisms grow well attached to zoogloea and poorly when exposed in the mixed liquor. Under low dissolved oxygen they proliferate massively and cause bulking. Understanding that balance explains most of what follows.
Three numbers that describe a sludge
The sludge settling ratio (SV), mixed liquor suspended solids (MLSS) and sludge volume index (SVI) describe performance between them, and each answers a different question.
- SV is easy to measure but incomplete. It does not fully reflect sludge quality and quantity. Normal values in municipal plants sit at 20%-30%, while some industrial plants operate normally above 90%; each plant has to establish its own optimum from operating experience.
- MLSS reflects quantity. The mixed liquor must hold a relatively fixed sludge concentration to keep treatment performance and system stability. Every activated sludge process has its own optimum concentration.
- SVI reflects flocculation and settling together. Too low means small flocs with poor activity. Too high means poor settleability, and bulking is imminent or already present.
Reading the microfauna
The microscope gives an early warning that no chemical test provides. Dominant stalked ciliates such as Vorticella, Epistylis, Opercularia and Zoothamnium indicate flocs that settle and flocculate well, with rotifers and other metazoa appearing alongside. Large numbers of free-swimming ciliates such as Colpidium, Colpoda and Paramecium mean the zoogloea are not yet developed and the aeration system is still starting up. Masses of Anisonema-type gliding flagellates point to anaerobic conditions in the tank. Explosive reproduction of amoebae and rotifers signals over-aeration with settling already deteriorating. Abundant Aspidisca, Testudinella and Trichocerca mean the influent load is extremely low. A sharp drop in Aspidisca means shock loading or toxic substances. Flagellates appearing, usually only Bodo and Oikomonas, means sludge performance is poor. When both protozoa and metazoa disappear, the sludge is in extremely poor condition. Slowly crawling forms such as Litonotus, Chilodonella and Stylonichia returning, as in the start-up phase, means recovery is under way.
Filamentous bulking versus the other kind
Filamentous organisms have a large surface area and outcompete zoogloea bacteria for carbon sources and other nutrients in the mixed liquor, multiplying massively and causing bulking. The same surface advantage favours them when water temperature suits, at low dissolved oxygen, and at low pH where fungal filaments survive better than zoogloea bacteria and overgrow.
Non-filamentous bulking is a deterioration of settleability caused by abnormal physiological activity of the zoogloea bacteria themselves. It takes two forms. In the first, the influent carries too much soluble organic matter, so sludge loading (F/M) is too high while nitrogen, phosphorus and other nutrients are insufficient, or dissolved oxygen in the mixed liquor is low. In the second, the influent contains relatively toxic substances that poison the sludge, so bacteria cannot secrete enough viscous material to form flocs, sludge-water separation in the secondary clarifier fails, and the sludge disintegrates. In practice, more than 90% of bulking is caused by filamentous organisms and less than 10% by non-filamentous causes.
Ageing sludge and rising sludge
Aged sludge looks dark and dull with weakened bioflocculation. Biological foam accumulates on the tank surface, flocs compress well but fine poorly settling particles remain in the supernatant and make the effluent turbid, and sometimes a thin floating layer forms on the clarifier. Two conditions cause it: high loading, where abundant organics drive vigorous synthesis and decomposition and produce excess young sludge whose poor settling leaves free bacteria behind; and low loading, where endogenous respiration dominates and the sludge ages.
Sludge that rises instead of settling has its own list of causes: excess surfactants and oils, pH too low or too high, salinity too high or changing too fast, water temperature extremes, highly toxic substrates, over-aeration, oxygen deficiency in the mixed liquor, denitrification releasing nitrogen gas, excessive return sludge flow, sludge accumulation in the clarifier, and filamentous overgrowth.
A daily walk-through checklist
Observe colour and odour of the sludge, check aeration effectiveness, watch aeration time and aeration rate, monitor waste sludge discharge and return sludge flow, and observe sludge conditions in the secondary clarifier. None of these replaces SVI on a trend chart, but together they catch a drifting plant days before the effluent shows it.