Home News Knowledges Polymer-Flooded Reinjection Water: Why the Filter Bed Cakes, and Where to Start

Polymer-Flooded Reinjection Water: Why the Filter Bed Cakes, and Where to Start

2026-11-18 13 readings

What changes when polymer enters the water

Reinjection water from polymer-flooded blocks is not ordinary produced water with a little more oil in it. Its signature is a combination: high polymer content, high viscosity, high oil content and a very stable emulsion. The polymer raises the viscosity of the aqueous phase and simultaneously adsorbs onto the oil-water interface, thickening the interfacial film. Once oil droplets are broken up they neither rise easily nor coalesce.

These four characteristics compound rather than add. High viscosity blunts gravity settling and flotation. Strong emulsion stability means residence time alone will never separate the phases. High oil content pushes the downstream filter to its load limit. Difficulty does not increase linearly; it accelerates.

Why the three-stage train with flotation stalls

The conventional three-stage-plus-flotation flow was designed around ordinary produced water. Nothing in it addresses demulsification or viscosity reduction, so oil removal efficiency falls short, effluent misses reinjection quality, and sludge volume climbs. Sludge is the hidden bill: oily sludge needs dedicated disposal, and the larger the volume, the higher the transport, treatment and management cost. When the flow loses efficiency it also demands heavier chemical dosing, which inflates sludge further. That is a closed loop of rising cost.

The caked filter bed nobody budgets for

High-molecular-weight polymer acts on the filter bed slowly and persistently. After entering the bed it binds loose media into a caked layer; differential pressure rises, backwashing stops restoring the bed, and media life shortens. Operators see frequent backwashing and deteriorating effluent, and rarely trace the cause upstream.

This also explains why strengthening filtration cannot solve the problem. While the polymer remains, even the best media only buys a slightly longer cycle. The polymer has to be dealt with before filtration, not after it.

Step one: chain scission instead of filtration

The SINOKLE process puts CDOF catalytic oxidation viscosity reduction at the front. CDOF is an integrated ozone advanced catalytic oxidation and flotation unit combining multiple ozone catalytic oxidation technologies, hydrodynamic cavitation and cyclonic flotation. The package comprises an oxygen generation system, an ozone generation system, a high-efficiency ozone dosing system, a multiple catalytic reaction system and a cyclonic dissolved-gas flotation system.

Its strength is mechanism synergy. Homogeneous and heterogeneous catalysis act together, hydrodynamic cavitation creates locally extreme conditions, supercritical catalytic oxidation accelerates the reaction rate, and cyclonic dissolved-gas flotation completes the separation, all under closed and pressurised conditions. The combination delivers solid removal of petroleum hydrocarbons, suspended solids, colloids, COD, bacteria and other pollutants.

Applied to polymer-laden water, CDOF takes on chain scission and viscosity reduction. Patented oxidation technology breaks down and degrades the large polymer molecules in the water; viscosity drops sharply, emulsion stability weakens, and the chronic caking of downstream media stops being inevitable. This is the starting point of the whole process and the most fundamental difference from a conventional train.

Step two: CDFU finishes the oil removal

Only once viscosity has come down can oil removal be efficient. CDFU uses microbubbles together with cyclonic flotation to break the emulsion and remove free oil, emulsified oil and suspended solids. The microbubbles give fine oil droplets an attachment surface, the cyclone field amplifies the density difference and speeds separation, and demulsification targets the residual interfacial film. Working together, these mechanisms strip out in a single step the oil released by upstream viscosity reduction.

Step three: polish, buffer, reinject

Produced water then passes a fine filter for deep polishing and flows into the reinjection buffer tank for on-spec reinjection. Because the polymer has already been cut in the CDOF stage, media caking risk falls sharply and the filter runs steadily, easing backwash frequency and media replacement.

Closing the loop on crude

CDOF and CDFU collect the recovered crude oil, which returns to the crude tank for reuse. Oil removal should not turn oil into waste; in a polymer-flooded block that oil still has recovery value, and for the water system it means less oily sludge to dispose of.

The complete route runs as follows. Polymer-laden water passes a coarse filter that traps debris, enters CDOF for catalytic oxidation viscosity reduction, then CDFU cyclonic dissolved-gas flotation completes demulsification and oil removal. The produced water is polished in a fine filter, flows into the reinjection buffer tank and is finally reinjected into the reservoir. The unit runs fully enclosed and pressurised, so neither ozone nor oil vapour escapes, and the skid-mounted design makes on-site layout and retrofit tie-in straightforward.

Where this route does not apply

Three boundaries are worth stating plainly. Where polymer concentration is low, conventional flotation may already meet injection quality and the CDOF stage becomes an unnecessary cost. Where salinity is extreme, material selection for the ozone train drives the budget more than process design does. And where the block has no crude recovery system to accept returned oil, the collection step loses part of its payback, though the sludge reduction still stands.