Home News Knowledges Effluent Out of Limits? A Parameter-by-Parameter Diagnosis for BOD5, Ammonia, TN, TP and SS

Effluent Out of Limits? A Parameter-by-Parameter Diagnosis for BOD5, Ammonia, TN, TP and SS

2026-11-17 8 readings

Every operator eventually meets the same morning: the lab report says one of the big five — organic matter, ammonia nitrogen, total nitrogen, total phosphorus or suspended solids — is over the limit. A well-designed and well-run conventional activated sludge process should hold BOD5 and SS below 20 mg/L, so when either drifts, something structural has changed. The good news is that the causes sort into a small number of families, and each family has checkable numbers attached to it.

Organics: BOD5 and COD Above the Limit

Organic removal fails for four recurring reasons. Nutrients come first: ordinary municipal sewage carries nitrogen, phosphorus and the rest in ample surplus, but when industrial wastewater makes up a large share of the flow, verify that the carbon-to-nitrogen-to-phosphorus ratio satisfies 100:5:1 — dose ammonium salts where nitrogen is short, and phosphoric acid or a phosphate salt where phosphorus is. pH comes second: municipal sewage sits near neutral at pH 6.5 to 7.5; small drops trace to anaerobic fermentation in the sewer, rainy-season drops to acid rain that is particularly conspicuous in combined systems, and sudden large swings almost always mean a slug of industrial wastewater has entered — correcting which means dosing sodium hydroxide or sulfuric acid at considerable cost. Oil and grease come third: high oil content makes aeration equipment work less efficiently, degrades the settleability of the sludge, and in severe cases becomes the cause of sludge bulking that pushes effluent SS over the limit — an oil-removal unit in pretreatment is the fix. Temperature comes fourth, changing microbial activity in winter, setting up density currents and short-circuiting in the clarifier, raising viscosity, and in summer lowering dissolved-oxygen saturation so the air supply must increase to deliver the same mass of oxygen.

Ammonia: The Nitrification Checklist

Nitrification is a low-loading extension of the conventional train, and its failure points are countable. Sludge loading: F/M must run at 0.05 to 0.15 kg BOD/kg MLVSS·d — the lower the load, the more completely NH3-N converts to NO3-N. Sludge age: nitrifying bacteria grow slowly, so if SRT is too short and sludge concentration low, the population never establishes; nitrogen-removal systems typically run SRT of 11 to 23 days. Return ratio: hold 50 to 100 percent, because too small a return lets denitrification set in inside the secondary clarifier and floats the sludge. HRT: the nitrifying basin needs at least 8 hours, because the nitrification rate is far lower than the rate of organic removal. Carbon ratio: the BOD5/TKN ratio — TKN being the sum of organic and ammonia nitrogen — governs the nitrifier share of the sludge; operating experience puts the optimum around 2 to 3. The nitrification rate, ammonia converted per unit sludge per day, typically lands near 0.02 g NH3-N/g MLVSS·d. Dissolved oxygen: nitrifiers are obligate aerobes whose uptake rate is far lower than that of the organic-decomposing bacteria, so DO in the aerobic zone must be kept above 2 mg/L and raised further in special cases. Temperature: below 15 °C the nitrification rate falls sharply, and below 5 °C physiological activity stops altogether — which is why winter ammonia excursions concentrate at plants in northern regions. pH: activity peaks between 8 and 9, is suppressed below pH 6.0 or above 9.6, so hold mixed-liquor pH above 7.0 wherever possible.

Total Nitrogen: Adding Denitrification

Denitrification reduces nitrate to nitrogen gas under anoxic conditions and inherits every nitrification prerequisite — only good nitrification gives efficient, stable denitrification. Loading stays low and sludge age long. The external return ratio can actually drop below 50 percent: most of the influent nitrogen is already removed, clarifier nitrate is modest, and denitrifying sludge settles fast, so the return can be lowered to extend residence in the aeration basin — while the internal mixed-liquor return runs between 300 and 500 percent. The denitrification rate typically falls at 0.06 to 0.07 g NO3-N/g MLVSS·d. The anoxic zone wants DO ideally zero, though holding below 0.5 mg/L in real operation is already difficult, and that constraint caps the denitrification process and the effluent TN with it. Carbon is the quiet killer: the BOD5/TN ratio must supply enough organic carbon for the denitrifiers, and at many plants the sewer delivers BOD5 below design value while nitrogen and phosphorus arrive at or above it — excess TN follows. pH tolerance is generous, metabolism normal between 6 and 9 with the optimum at 6.5 to 8.0. Temperature matters less than for nitrifiers but still peaks at 30 to 35 °C, drops markedly below 15 °C and nearly stops near 5 °C — so winter defense means lengthening SRT, raising sludge concentration or bringing more basins into service.

Total Phosphorus: The Anaerobic-Aerobic Balance

Biological phosphorus removal places an anaerobic zone ahead of the aerobic one so phosphorus-accumulating organisms alternate between release and uptake, exporting phosphorus with the wasted surplus sludge. Loading runs deliberately opposite to nitrification: a high-F/M, low-SRT system at F/M of 0.4 to 0.7 kg BOD5/kg MLSS·d and SRT of 3.5 to 7 days — without dropping so low that effective BOD5 removal can no longer be guaranteed. The BOD5/TP ratio entering the anaerobic zone should exceed 20, because the PAOs — physiologically weak Acinetobacter that take up only readily degradable organics — need sufficient BOD5 for normal metabolism. Oxygen control is split-brained: the anaerobic zone must sit below 0.2 mg/L for effective release, while the aerobic zone must hold above 2.0 mg/L for efficient uptake; river-water influent with high DO fed straight to the anaerobic zone quietly sabotages the release step. Return ratio should be low but fast — 50 to 70 percent where settling is good — withdrawing sludge before the PAOs meet anaerobic conditions in the clarifier and release their phosphorus. The anaerobic HRT needs 1.5 to 2.0 hours for full release, the aerobic zone 4 to 6 hours for full uptake, and mixed-liquor pH works best between 6.5 and 8.0. As the TP limit tightens, chemical removal increasingly joins the biology — raising performance but also multiplying surplus sludge and cake to dispose of, so the dosing point and dose belong to jar testing, adjusted promptly for the lowest chemical consumption.

Suspended Solids: It Is the Clarifier

Effluent SS rides on sludge quality and secondary clarifier hydraulics. Plants that shortened clarifier design HRT to save construction cost and pushed hydraulic surface load up suffer repeated sludge boilover; process adjustments that demand a high sludge concentration in the biological basins push the solids load past what the clarifier can carry. Three parameters decide the outcome. Clarifier HRT of 3 to 4 hours guarantees flocculation and high settling efficiency. Hydraulic surface load — 0.6 to 1.2 m³/m²·h generally recommended — sets the smallest removable particle: the lower the load, the more particles settle out. Solids surface load should not exceed 150 kg MLSS/m²·d; beyond it the sludge blanket climbs, flocs leave before settling, and effluent SS suffers. Sludge quality completes the picture with four virtues: good adsorption for colloidal pollutants, high biological activity, good settleability and good thickening. Weakness in any one of the four shows up in the same place — the effluent channel.